Announcement

Collapse
No announcement yet.

2000 Maristar with $$$ in parts and months of time

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • JimN
    replied
    Originally posted by Mystic3D View Post
    Yes Sir, If I counted my time, pretty insane $.

    Boat to do list(Complete):

    Replace MAF-done
    This boat doesn't have a MAF sensor, it has a MAP sensor unless it was modified. If it does have a MAF sensor, it should also have an IAT (Intake Air Temperature) sensor.

    Leave a comment:


  • Mystic3D
    replied
    Originally posted by gweaver View Post
    Can you post pictures of the GSA system and the problem with the transom? I've been thinking about trying this- the suction cup wake device works well, but I'm intrigued with tabs. Can you maybe explain what the issue is? Tabs too wide- not enough mounting surface to attach? Not enough space to mount the actuator?

    G
    The GSA System is sitting in my garage, still sealed in the box. I used the templates off wave makers to see how I was going to get it to fit. I also have a roll of Seadeck brushed Tan I have sitting there.
    Attached Files

    Leave a comment:


  • Mystic3D
    replied
    Attempt at Wedge

    So I wanted to build something that fit the contour of the hull, secured with Velcro, So success on that front, this is built out of a Foam Block, 8 layers of 8oz glass, then gelcoat, sanded.

    Wave result, not great.
    Attached Files

    Leave a comment:


  • Mystic3D
    replied
    Originally posted by bturner2 View Post
    You have some serious jack tied up into this project.

    The workmanship and quality of the installation look great. Nice work!
    Yes Sir, If I counted my time, pretty insane $.

    Boat to do list(Complete):
    Alternator not charging- put 50A back on - done
    Center locker ballast hose too long-done
    Left most vent leaking water-done
    Speakers whining ordered new connectors 4-19-done
    Tower Speakers rotating -file a flat-done
    Speed control not holding speed-done
    Front Ballast Polarity Reversed=done
    Neoprene sleeve for wakeboard bungee - ordered 4-19-done
    Latch strap needs securing-done
    Cap off rear engine steam vent-done
    Replace hose between flush pro and thru hull-done
    Check strainer seal-done
    Rotate manifold drain valves-done
    Replace Switch Covers-done
    Blower-done
    Pump-done
    NAV-done
    Courtesy-done
    Underwater Light-done
    Rear check valves for fill not working-Ordered new style check valve from wavemakers-done
    Misfire at high rpm
    Spark plug wire resistance- 3=6k, 1=4747(bad), 5=6.9k, 7=8.9k,
    Right bank spark plugs white=lean
    Left bank =lean
    Replace spark plug wires-done
    Replace MAF-done
    5/19/2015
    Fasten deck platform bracket-done
    Adjust throttle cable-done
    Install trailer lights-done
    Replace ft bag fitting-done
    Not shifting into Reverse - Adjusted
    Windshield Jammed - Fixed
    Ski Locker - Sand top so smooth
    Whine speakers
    Stock Injector:
    RP(Rochester) Injector W 83(each one different)
    Part # 17121068
    12.1 Ohms 256cc at 3 bar
    24 lb
    Replace Injectors Bosch - done

    Leave a comment:


  • bturner2
    replied
    You have some serious jack tied up into this project.

    The workmanship and quality of the installation look great. Nice work!

    Leave a comment:


  • gweaver
    replied
    Can you post pictures of the GSA system and the problem with the transom? I've been thinking about trying this- the suction cup wake device works well, but I'm intrigued with tabs. Can you maybe explain what the issue is? Tabs too wide- not enough mounting surface to attach? Not enough space to mount the actuator?

    G

    Leave a comment:


  • Mystic3D
    replied
    Stereo Install

    Add a 3rd Battery, All new Wire. JL AMP's, Now has a Blower Motor across the AMP's to keep them cooler.
    Attached Files

    Leave a comment:


  • Mystic3D
    replied
    Replace Medallion Gauges

    Replace Medallion MDC-1600 and Gauges with Faria, Thanks to the thread on TeamTalk
    Attached Files

    Leave a comment:


  • Mystic3D
    replied
    Ballast Install

    All Wavemakers, MC Relay Box(the right way), measure, drill a bunch of holes on he bottom/sides. Drain/Vent out of the side, Fill in the bottom, 3 pumps, one for KGB, 1 for each rear locker 720. Divider supports from wave makers
    Attached Files

    Leave a comment:


  • Mystic3D
    replied
    Samson Tower Install
    Samson is amazing to work with, super high quality stuff, The tower was measure, measure, had to be super MCOCD to do it right.
    Attached Files

    Leave a comment:


  • 2000 Maristar with $$$ in parts and months of time

    Figured I would post what I have done to this as it might give people ideas of what can be done.
    Now I have a GSA system Black Anodized with Platform Brackets sitting in the garage as I cannot see how it's going to work due to transom design. So almost there with a boat that can surf.
    Now about to pull the trigger on a 19 Star...

    1. Trailer Wheel Bracket - To allow wheels to hit before bottom of trailer on steep inclines.
    The white lights are Backup Lights


    Last edited by Mystic3D; 09-28-2019, 11:47 PM.
Working...
X