What Work did you do on your Mastercraft Today?

[dbatteiger]

XM radio

Put XM in boat. Love it. I want to do a valve job on 1700 hours 93 351, are any of you hesitant to the fact that you should never do the top end without doing the bottom end? Kids are gone and we don't run wide open anymore... Thoughts Waterlogged?

[lakedrum03]

If you are taking the time to rebuild the top end, why not freshen up the whole thing? You are going to be there, might as well do it.

Just my 2 pennies.

[Mark rsa2au]

Just got the last piece to the puzzle, yesterday. I did a 500 hour service which included the following:

New Spark Plugs
New Distributor Rotor and Cap
New Belt
New Impeller and Water Pump Seal
New Knock Sensor Plugs
New J house (metal vs rubber)

While I was in there, I also gave the engine a detail by polishing all the pulleys, touching up some paint, adding rubber covers to all the hose clamp ends and putting an aluminum pulley on the alternator. Most probably would not even notice the difference, but my OCD is satiated for a little while.

Hey Sodar, looks great!!!

Would love to know where you got the metal J Hose???


Sent from my iPhone using Tapatalk

[Sodar]

Looks great.. how did u the metal jhose? Your OCD must be slipping a bit.. surprised you did not replace screw clamps with t bolt clamps... [emoji109][emoji109][emoji109]

Sent from my SM-G955U using Tapatalk

HAHA. Not sure what you are saying about the Metal J-Hose, but if you are accusing me of a dent, I politely tell you to pound sand. The hose is formed in 2 pieces and that is where they join.

As for the T-clamps.... I actually had the thought, but then got to looking at size and quantity and decided against it. I did buy a 10 pack of Breeze clamps to match factory at the locations where added fittings had been installed.

Hey Sodar, looks great!!!

Would love to know where you got the metal J Hose???


Sent from my iPhone using Tapatalk

I got everything from Bakes Marine. They have been awesome for the Indmar stuff.

https://www.bakesonline.com/indmar-circulation-pump-to-t-stat-housing-formed-metal-hose.html

[cbryan70]

HAHA. Not sure what you are saying about the Metal J-Hose, but if you are accusing me of a dent, I politely tell you to pound sand. The hose is formed in 2 pieces and that is where they join.

As for the T-clamps.... I actually had the thought, but then got to looking at size and quantity and decided against it. I did buy a 10 pack of Breeze clamps to match factory at the locations where added fittings had been installed.



I got everything from Bakes Marine. They have been awesome for the Indmar stuff.

https://www.bakesonline.com/indmar-c...etal-hose.html

Cam looks like your motor cover insulation is going...time to replace it

[Tom_S]

Upgraded my paddle wheel to NauticLaugic GPS, upgraded my steering wheel, replaced my old winch with a new Fulton F2, replaced the trailer jack with an F2 to match the winch & replaced the boat buddy with a Ramp-&-Clamp!




Sent from my iPhone using Tapatalk

How do you like the RnC with the lever out the front? Is it easily accessible with the winch line? I wrote them an email yesterday on which version would work on my trailer and have yet to hear back.

Sent from my SM-G965U using Tapatalk

[Prostar 190]

Got rained out of a lake today so gave her another coat of wax.

[motomario]

Got rained out of a lake today so gave her another coat of wax.

Great metal flake view!What kind of brand wax and foto if it possible?

[Prostar 190]

That was Meguire's flagship premium wax and I took the photo with my cell phone which is a Google pixel 3 xl.

[Gianfranco]

How do you like the RnC with the lever out the front? Is it easily accessible with the winch line? I wrote them an email yesterday on which version would work on my trailer and have yet to hear back.

Sent from my SM-G965U using Tapatalk

Man I absolutely love it!! Works so much better than the boat buddy I had on there!! Haven’t have any issues with the clamp getting on the way, I have just enough room.


Sent from my iPhone using Tapatalk

[waterlogged882]

Man I absolutely love it!! Works so much better than the boat buddy I had on there!! Haven’t have any issues with the clamp getting on the way, I have just enough room.


Sent from my iPhone using Tapatalk

If your Boat Buddy is available and in decent shape, I am interested in it please.

.

[motomario]

That was Meguire's flagship premium wax and I took the photo with my cell phone which is a Google pixel 3 xl.

thank you for the information, I will wait for the photo.is this the one ?https://www.ebay.com/itm/Meguiars-M6...-/172599073724

[Prostar 190]

thank you for the information, I will wait for the photo.is this the one ?https://www.ebay.com/itm/Meguiars-M6...-/172599073724

Yes Sir!

[john noonan]

Traded it in on a Tige!!!!!!


Sent from my iPhone using Tapatalk

[Ry_nihilation]

Getting ready for a Shasta trip this week so I have a very busy weekend! Like always I had to pick the hottest weekend of the year! Got a lot of great tips from this forum, thank you for the help.
-Changed Engine Oil
-Changed Transmission Fluid
-New Impeller
-Cleaned Air Filter
-Installed Engine Divider Braces from WakeMakers
-Fixed a Gel Coat Nick
-Glued Down Lifting Edges on Swim Step,(Almost done)
-Glued Up Stereo Cables that Fell Down
-Vacuumed and Shampooed the Carpet
-Three Step Cleaned the interior
-Washed the Exterior(Two Step Detailing/Wax this week)
-Ordered Bow Pieces from Gator Step (4-6 week lead time)
-Trying to Figure Out Where and How to Use the Cup Holder Garbage Can