Go Back   TeamTalk > View Profile

Engine Nut Engine Nut is offline

TT Enthusiast

Visitor Messages

Showing Visitor Messages 1 to 10 of 17
  1. Greenielife
    05-28-2019 11:52 PM
    Thanks for the heads up! Where are you located and how would I order the tbi plate? Indmar P/N 536049
  2. Mark N
    05-21-2018 02:23 PM
    Mark N
    Hi Engine, I was told another member that you are the resident guru on engines on this board. I have a MasterCraft CSX 265 with LY6's that apparently needs new exhaust manifolds. As you know the original manifolds are no longer being manufactured and the replacements don't fit in a twin engine set up. Do you have an answer of how to fix? Thanks so much.
  3. CBA
    06-07-2017 10:46 PM
    Hi there Engine Nut,

    Taking a long shot here but was hoping you could help out. Have 2008 LY 6.0 motor(X-45) that needs 2 new exhaust manifolds as the original ones are leaking and corroded. It appears I can find a two piece replacement (manifold & riser)part but I don't seem to be able to find a single cast one that came with the factory motor. Is there anyone who still makes the single piece cast aluminum one? If not is there a certain 2 piece (manifold & riser) replacement one that you recommend I get? Does it really matter if it's 1 piece or 2 piece?

    Thank you very much in advance for any help or guidance you can provide.

    Joe Lowden
  4. Rsgessele
    05-30-2017 10:03 PM
    Not sure if my last message got posted, I am trying to replace harmonic balancer 99 xstar LT1, any help would be greatly appreciated
  5. Rsgessele
    05-30-2017 09:35 PM
    Trying to replace my harmonic balancer please help!
  6. mastat150
    07-09-2016 10:53 PM
    I understand your the man to ask when it comes to Indmar problems. I just bought an 07 X45 with a 6.0 has 400 hours on it. The first day I have had it I ran it about an hour or so then stopped for a while to swim for about 20 min. When I started it back up It ran rough then went into limp home mode and had check engine come on. I started to limp back to the marina but being a considerable distance I shut it down (even thought the girlfriend suggested not to) and it wouldn't start back up. It would turn over start up then die right away. I had initially thought it was a fuel pump issue since that seems to be a common problem so the dealership I bought it from sent me a new one. They didn't send the gasket or adapter so since I needed to order those and had a full tank of gas I figured the best thing to do would be just to take it to the dealer since I was getting the check engine before I got into changing the pump out and If they thought it was the pump just let them change it. I took it to Boat House Marine Tri Lakes in Ohio that was highly recommended for service. They are two hours away but that is basically how far any Mastercraft dealers are from the Pittsburgh, Pa area. The boat is currently there and I talked to them this morning and they told me that it is throwing a bunch of codes and are stumped at the moment. They said the pump was reading just fine so they didn't put the new one in as of yet and that they were going to have to call Indmar on Monday to see if they have any insight on the problem. They have never seen an issue like this on a 6.0 before. Now I know it would be way more helpful if I could tell you what codes it is throwing but I failed to ask when I was on the phone and they are closed until Monday. My question for you is have you ever run into anything like this and possibly have any suggestions I may pass along or have them look into. They told me that hopefully it was one thing and it could be triggering all the other codes if not they would have to address them one at a time. I am just a nervous wreck about it since I have just bought the boat and have only had it on the water once on my own since purchase and prior to that it was fine. I am hoping to not have a huge issue or service bill since I have spent a good bit of money for the boat purchase. I purchased it in South Carolina and am in Pennsylvania so its not as easy as having the place I purchased it from take care of the problem. I was happy they sent me a fuel pump since they are quite pricey and since it was a used boat they don't exactly carry a warranty plus it ran fine down there. I have read some people having the stock Mastercraft cruise control causing some problem or a ground issue some where which maybe something giggled loose or became pinched with the long trip home???? At this point I'm just guessing and by no means am a boat technician.

    I have an 87 Pro Star with a Indmar 351 and I can fix pretty much anything on the since there are no computers or electronics. Thank goodness I have kept that boat- In almost 30 years that has never once given me a lick of trouble (Knock on wood). I'm very fortunate I still have a boat to use but it sucks with the new one in the shop. Since I'm a ford guy I blame it on the fact that the new one is a gm motor and my ol' reliable pro star is a ford, lol. I apologize for being long winded and possibly not having enough info to go on but any input would be more than appreciated. Thank you in advance!
    email: [email protected]
  7. Fullpass
    10-31-2015 12:01 PM
    If you could help, would be great..REMOVEL INSTALL INSTRUCTION.I just sent an email to [email protected] from [email protected] for balancer/hub removal two piece unit for a LTR late 2002 early 2003...GUESS YOUR THE MAN ON HERE SO TO SPEAK...anyway to get a service manual for this motor...others dont seem to cover this motor.
  8. Engine Nut
    01-12-2015 07:15 PM
    Engine Nut
    So when it acts-up, if you stop and go back to the beginning and start through the course again it does the same thing? I agree with the others on the thread. You may have to find a dealer and have them do a Diacom recording of the run so we might be able to see what is going on. Sounds like it is running out of fuel but if the pressure is holding at 58-62 PSI it should be OK.
  9. weist1013
    06-23-2014 09:50 AM
    looks like im gonna need some help? i have a 2001 230 vs that needs real trans seal replacement. do you sell the parts or know where to get them? thanks in advance.
  10. Jorski
    06-23-2013 04:11 PM
    Hey Engine Nut,

    My 1993 LT1 has the original spark plug wires. While they look fine, the must be overdue for a change.

    What do you recommend?



About Me

  • About Engine Nut
    Team MasterCraft Member
  • Signature
    Engine Nut
    Indmar Marine Engines
    Power to the Sport


Total Posts
Visitor Messages
General Information
  • Last Activity: 07-29-2019 06:26 PM
  • Join Date: 04-14-2005
  • Referrals: 0


Showing Friends 1 to 7 of 7

All times are GMT -4. The time now is 01:20 PM.