Announcement

Collapse
No announcement yet.

Search Result

Collapse
56 results in 0.0277 seconds.
Keywords
Members
Tags
  •  

  • N8111z
    started a topic 91 prostar electrical issues

    91 prostar electrical issues

    All the sudden my 91 prostar has started showing some weird electrical issues. For example if I hit the blower switch nothing will happen accept for the engine temp gauge goes pegged. Another example is the bilge pump not turning on accept for when I barley crank the motor, the pump will then run for...
    See more | Go to post

  • N8111z
    started a topic 91 prostar 190 heater

    91 prostar 190 heater

    Was there a particular heater that came standard on the 91 ps190s? I couldn’t find a model or brand name on the one that I have in my boat. I am looking for what I assume are freeze plugs on all four corners of the heater unit. If anyone is familiar I’d appreciate it!
    See more | Go to post

  • While I’m thinking about it, I’m also dealing with the shifter engage lever right below the ball on the shifter knob that does not want to lock back into place in neutral, I have to manually push it in place. Is there a single replacement for this? Or will it require a whole new shifter assembly?
    See more | Go to post

    Leave a comment:


  • Just the wand. Thanks for the strut model!!
    See more | Go to post

    Leave a comment:


  • N8111z
    started a topic Prostar anchor light and seat strut

    Prostar anchor light and seat strut

    I need to get a new anchor light for a 91 prostar 190. Does anyone know a oem, or equivalent to oem replacement? I also need a new gas strut for the observers seat but didn’t know what pressure size to get. Thanks!
    See more | Go to post

  • N8111z
    started a topic 91 prostar 190 alignment troubles

    91 prostar 190 alignment troubles

    I’m working on doing an alignment on my 91 ps190. I need to bring the motor probably 1/4 inch to the port side. The motor will slide fine to the starboard side, but will only go back to the original position and no farther to the port side like I need it to. Has any one has this problem before? Maybe...
    See more | Go to post

  • N8111z
    started a topic 91 ps190 thermostat

    91 ps190 thermostat

    I’m looking to replace the thermostat on a 91 prostar 190 as the old one is no good. I did a little research and found that it seems like a lot of people recommend the 160 degree thermostat as opposed to the 143 degree thermostat. I was curious to get current opinion of what route to go and what type...
    See more | Go to post

  • N8111z
    replied to mastercraft nameplate on x24
    Where did you get the custom nameplate made?
    See more | Go to post

    Leave a comment:


  • N8111z
    started a topic 91 prostar 190 electrical problem

    91 prostar 190 electrical problem

    I recently got a 91 prostar 190 and am having an electrical issue. My problem is that I am not getting the starter solenoid to close via the key. I know the solenoid is good since I tried putting the start signal wire over to the battery power post and you can hear the solenoid closing. Also, when I...
    See more | Go to post

  • N8111z
    started a topic 91 prostar battery question

    91 prostar battery question

    Does anyone know if the 1991 prostar 190s came with a battery On/Off switch? I am looking at one currently and when I hooked up 2 different, fully charged batteries nothing on the boat will power up. I tried following the main power cables as far as I could see but they dive under the floor and I couldn’t...
    See more | Go to post

  • N8111z
    replied to Gel coat and fiberglass damage?
    I was also curious if anyone would be concerned about the rust build up on coupler that attaches the prop shaft to the transmission? Also the floor of the bilge looked flaky only around the engine. Would this be from heat? These are probably the basic new guy questions but I am happy to take that t...
    See more | Go to post

    Leave a comment:


  • N8111z
    replied to Gel coat and fiberglass damage?
    Thank you everyone for the great input, it is greatly appreciated! I’m looking at the boat from the standpoint of wanting to keep it for a while, but also not getting to upside down on it Incase I do decide to sell it at some point.

    Has anyone had any experience rebuilding a new rear...
    See more | Go to post

    Leave a comment:


  • N8111z
    replied to Gel coat and fiberglass damage?
    Here are some more pictures, if there is anything that catches someone eye, I’m all ears! Also not sure if I mentioned it before but the rear seat is also not with the boat so that’ll be taken into account in any offers....
    See more | Go to post

    Leave a comment:


  • N8111z
    replied to Gel coat and fiberglass damage?
    thank you all for the great input! I went and took a loot at the boat today and it is really solid. Definitely a little rough around the edges, but the bones are there. Looks like it well maintained and winterized correctly from what I could tell. What does everyone thing a fair price would be for the...
    See more | Go to post

    Leave a comment:


  • N8111z
    replied to Gel coat and fiberglass damage?
    thank you all for the great input! I went and took a loot at the boat today and it is really solid. Definitely a little rough around the edges, but the bones are there. Looks like it well maintained and winterized correctly from what I could tell. What does everyone thing a fair price would be for the...
    See more | Go to post

    Leave a comment:

Working...
X